
November 18, 2026
Details That Close the Loop: Innovations in Circular Design
In the latest episode of Deep Green, host Avinash Rajagopal sits down with Jonathan Mountfort, creative director at Autex Acoustics, and Julia Gillespie, vice president of marketing and sustainability at Momentum Group, to discuss how to simplify this complexity. Following a recent partnership between Momentum and Autex that brings Autex’s products to the United States, they talk through improving the circularity of conventional materials in their product categories, as well as innovating with new biobased and regenerative ones. Read an excerpt of their conversation below or listen to the full episode on the Surround Podcast Network.

Avi Rajagopal (AR): Within the interiors industry, we’re starting to talk a lot more about circularity. Especially with interior design and renovations, until very recently, we just accepted that all of that stuff would go to the landfill. Now we’re beginning to question that, and we see that work happening at the design scale, but also with manufacturers like Momentum and Autex. If you had to think of a couple of places where you’re seeing a mindset change and signs of progress, what would those be?
Julia Gillespie (JG): The industry itself is waking up, just like you said. The recycling component is probably the most difficult part.
I would say vinyl wallcovering is a little bit ahead because it’s more of a mono material. It’s easier to recycle, and they’re already getting some systems in place. Where we’re still struggling is textiles. One, because the deinstall is so difficult, and two, because there are so many components in a textile.
There are very few textiles that are a monomaterial, and if they are, they have a backing. That’s the egg we’re all trying to crack. I’m talking to people all the time, trying to find out how we can do it better. When we started partnering with Autex, it was a very different equation. I feel like they’re much further ahead than we are in the US.
While we’re all trying, there’s nothing built to scale to accommodate the recycling of many of these products. And the flip side is that at deinstall, people run out of time or money, and it goes to the landfill. But people are doing things. A lot of companies are doing a lot to make this better, and the industry is waking up. I think there will be industries that pop up from this.
AR: You know, I’m really hoping there’ll be an ecosystem of innovation here in the US too.
Many traditional, more established manufacturers have a harder journey because they’re already locked into systems that are not circular. They’re kind of pushing a boulder up a hill. They have complex product assemblies, lots of different materials and lots of things to deal with in an industry that’s also complex in itself. And we don’t have a design culture that really incentivizes reusing things or giving things back.
I think what makes the Autex story so great is that the company was sensitive to how it deals with materials from the very beginning and has a long legacy of thinking about sustainability. Maybe that has given you a platform to innovate even further today.
So why don’t you start by giving us some background on Autex and how you approach sustainability and circularity?
Jonathan Mountfort (JM): Autex has been using recycled materials since the late ’90s or early 2000s, but it’s really been put on steroids in the last 10 or so years. We were the first to do EPDs back in 2017, and then we started measuring our performance and looking at the impact we had.
It’s a phase of facing reality, I guess, is the best way of explaining it. You’ve got to understand what you’re doing to then chart the course for the next best thing. What’s the low-hanging fruit? So, from EPDs, we went to measuring our carbon across the organization in 2021, and then across all of our products in 2022, and we started offsetting. That gave us a roadmap, effectively, to go through and pick hotspots to target, so we could start minimizing the amount of carbon we had to offset.
I took over looking after the technical department in 2024. From there, being in charge of design, technical, and sustainability, we were able to layer all of these things together right at the beginning of developing any product. As soon as I had a question about something, I’d just go and bring in the technical team or the sustainability team and get a measure on it. “Hey, if I turn this from aluminum into plastic, what impact would that have? If I made it out of our own waste, what would happen?”
That gave us something we’ve now branded the Autex Future Lab, and we’ve got a team of people working on what’s the right thing to do. What’s the right thing to make? The question we asked was, “If we could make more of something and it got better, what would that thing be, and how does it work?” It comes from circular thinking and from biomimicry-style design thinking. A tree doesn’t apologize for making too many leaves. There aren’t too many cherry blossoms on a cherry tree in spring. They all land on the ground and go everywhere, and they all have somewhere else to go. It’s just a phase change. Everything in nature is changing phase all the time. We’re from nature. People are made of nature. We try to pretend we’re not, but we’re still skin and bone and all of that other good stuff.
The question we were asked is how we design businesses and systems that enable us to make more and be better. That’s when we started going, “Okay, once it’s been that, what’s it going to be next? And then what’s it going to be? And how does that output get better, not worse?”
AR: It’s good to go for the wins, right? It’s good to go for the things you can do today and get them done. But it’s also so important to always be aware of where your biggest problems are. Where’s the largest mass of material? Where’s the most energy being generated? Where’s the most waste being generated? And to tackle those. I love your analogy of the tree. We shouldn’t be scared of volume. It’s more about whether we’ve thought through the system. That’s so key.
Let’s focus on the material you deal with the most, which is PET. You’ve done so many amazing things with PET. Before you tell us what Autex has done, can you give us a sense of how much people in the industry are using recycled PET? Is it even a thing? And in interiors in particular, how are we doing on PET in general? And then how is Autex handling PET?
JM: Recycled PET is a thing. It’s abundant, there’s a lot of it, and it’s easy to recycle. It’s also easy to turn from one format into another, say from a bottle into a fiber or into textiles. It turns up in so many different places.
How are we doing on recycling PET? Once it becomes a fiber, it’s very difficult to turn it back into something rigid. But more and more technologies are coming out that make that possible, with examples all over the world, including Blocktex, Mura, and Lextra.
But that’s where it comes. It turns into a textile, and then it degrades through the textile life cycle. Each phase change, it might be a pair of running shorts or a puffer jacket or something like that, and then hopefully it becomes insulation or another mono material. But often it’s paired with wool and cotton and all the rest of it in a big jumble, and it becomes pretty difficult to categorize. Material keeps its value when it’s singled out. That’s probably the best way of explaining it.
AR: That’s why, Julia, you started out by talking about the complexity of textiles. Very few textiles are one material. They have many materials woven in. So once you take PET and turn it into a textile, it gets mixed up with all the other stuff, as you said, and then it becomes hard to separate. PET also has another problem: it’s very hard to upcycle, right? How is Autex dealing with PET?
JM: Well, we looked at that whole life cycle. We’ve taken it from a rigid polymer, turned it into a fiber, turned it into a textile, turned it into a panel. It sits in a panel in a fit-out for 6 to 10 to 20 years. Once it comes out, we have a very, very simple recycling method. It chops it up, puts it with a little bit more material, and turns it into a reform, which is basically reconstituted, and it goes into backings and soffit liners and insulation and things like that.
What’s really good about that step is that it’s a sequestration method. It’s somewhere you can put a huge volume of material that serves humanity for a really long time—50-odd years in the fabric of a building, insulating houses or doing something like that. And it keeps it pretty clean, so we can get it out again. But once it’s been chopped up, there was a hole in the loop. About four or five years ago, we started looking for a process that would take it back to a format we can use again.
We didn’t want to put too much energy into it. A lot of those processes are really energy hungry, and we didn’t want to have to re-melt repeatedly. We couldn’t find one, so we were playing around. We did a bit of a study and came across a machine and a process, well, a series of things put together in a really rugged way. We got some success pelletizing the PET through a custom-built machine that we’ve affectionately called the pelletizer, because it turns it into pellets. From there we thought, “Well, it’s a polymer, so we should be able to injection mold it.” So we worked with a really smart crew just out of Auckland, New Zealand, to come up with a way of making this pelletized material go straight into an injection mold without going through a repolymerization or re-melting step.
That meant we took a whole heat process out of the recycling and pumped it back up into a rigid polymer in one step. So, it goes from pellets to a product. From that we got a homogenous material, made of our own waste, that we can now use. That was the game changer. Now we’ve got a material that’s homogenous with our other material, in a process that takes it right back to the top of the tree again. It’s nearly as good as virgin, and it can go around and around and around.
AR: And now you’re using that rigid plastic for some of the components and fixtures and clips in your systems.
JG: Yes, you’ve removed adhesives, and made it easier to install, deinstall, and ultimately recycle.
JM: The first product using that material, we call RePET. Using RePET, my man Luke Walker in Auckland was like, “Well, if it’s made of that, it should friction-weld. Let’s give it a go.” So first up we 3D-printed it, and he made a little disc looking like a milk bottle lid and welded it to the panel, and he went, “Whoa, there’s something here, right?” And we were like, “Yeah, there is.” So, we designed Spinfix, a little friction-welded fixing that goes on the back of our panels, which means we can put them up without gluing them. It also puts a little air gap behind the panel. It stands it off the wall, which increases the acoustic effect, and when the panel comes off, you repair the wall by puttying up the holes and repainting it.
AR: It’s like a snap button. But the snap buttons are made of the same material that the panel is made of. There’s no glue or adhesive or screws. It’s like magic.
JM: That’s the little nugget of glory. It’s a tiny thing that makes a huge difference. And they can go through the pelletizer together, so it doesn’t matter.
AR: It’s incredible. You can take it off the wall and throw it in the pelletizer all in one piece.
Listen to “Details That Close the Loop” on the Surround Podcast Network.
Would you like to comment on this article? Send your thoughts to: [email protected]
Related
Viewpoints
Chromatic Architecture Makes a Case for Color
Chromatic Architecture: The Craft of Colour in Design, a new book by Adam Nathaniel Furman and Kate Mazade, shows through 34 case studies how color is inseparable from design and architecture.
Viewpoints
3 AI Architecture Tools Rethinking Workflows
From consolidating AI models to rethinking BIM and automating drawing-to-model conversion, tools like xFigura, Motif, and QikBIM target different points in architecture’s increasingly fragmented digital workflow. The g…

